How To Make Solar Panels
A solar energy panel transforms the energy from sun's rays into electricity. With the help of regular parts found close to your home, you too can create a solar energy panel and create electricity. The cleanest form of replenish-able energy available, solar power will significantly help reduce your power bill.
Here is a catalog you may need you will require you make a solar panel:
One electric stove (at least one thousand watts)
one half-square feet sheets of copper flashing
One 2-litre plastic bottle
One micro-ammeter
Three big spoons of table salt
Sheet metal shears
Electric drill with sand paper
Two alligator clip leads
A pair of safety goggles
A little tap water
Steps to make a solar panel:
1. First, clean off the copper flashing completely. If there's any rust on the flashing, take it off with sandpaper. With the help of the sheet metal shears, cut the copper flashing into size big enough to to cover the electric stove burner.
2. Now put the copper flashing on the electric stove burner and turn on the stove. The flashing should remain on the burner until a layer of black cupric oxide forms on it. This usually takes about thirty minutes.
3. Once the layer of cupric oxide has formed on the flashing, permit it to cool. Wipe the flashing so all the black cupric oxide is gone from its surface. However, make efforts to leave the red cupric oxide formed in the process, as it is.
4. Use the metal shears to chop another piece of copper flashing in the same size as the previous one. Take the 2-litre plastic bottle and cut its top off. Attach the 2 sheets of copper flashing to the insides of the plastic bottle using the alligator clips. The sheets have to be attached on the both sides of the insides of the bottle, and should not touch.
5. Connect the lead of the alligator clip of the clean copper flashing to the positive terminal of the ammeter. Now put the lead of the alligator clip of the red cupric oxide plate to the negative terminal of the ammeter.
6. Take some hot tap water and dissolve the table salt in it. Now pour this salt solution into the plastic bottle. But make sure that the salt water solution only covers the bottom of the two copper flashings. It shouldn't reach up to the level of the alligator clip leads.
7. Now place this set-up in sunlight. Watch the ammeter to tell the amount of electricity generated by this solar panel. While you set up your solar panel, be sure to wear your safety goggles all the time.
Here is a catalog you may need you will require you make a solar panel:
One electric stove (at least one thousand watts)
one half-square feet sheets of copper flashing
One 2-litre plastic bottle
One micro-ammeter
Three big spoons of table salt
Sheet metal shears
Electric drill with sand paper
Two alligator clip leads
A pair of safety goggles
A little tap water
Steps to make a solar panel:
1. First, clean off the copper flashing completely. If there's any rust on the flashing, take it off with sandpaper. With the help of the sheet metal shears, cut the copper flashing into size big enough to to cover the electric stove burner.
2. Now put the copper flashing on the electric stove burner and turn on the stove. The flashing should remain on the burner until a layer of black cupric oxide forms on it. This usually takes about thirty minutes.
3. Once the layer of cupric oxide has formed on the flashing, permit it to cool. Wipe the flashing so all the black cupric oxide is gone from its surface. However, make efforts to leave the red cupric oxide formed in the process, as it is.
4. Use the metal shears to chop another piece of copper flashing in the same size as the previous one. Take the 2-litre plastic bottle and cut its top off. Attach the 2 sheets of copper flashing to the insides of the plastic bottle using the alligator clips. The sheets have to be attached on the both sides of the insides of the bottle, and should not touch.
5. Connect the lead of the alligator clip of the clean copper flashing to the positive terminal of the ammeter. Now put the lead of the alligator clip of the red cupric oxide plate to the negative terminal of the ammeter.
6. Take some hot tap water and dissolve the table salt in it. Now pour this salt solution into the plastic bottle. But make sure that the salt water solution only covers the bottom of the two copper flashings. It shouldn't reach up to the level of the alligator clip leads.
7. Now place this set-up in sunlight. Watch the ammeter to tell the amount of electricity generated by this solar panel. While you set up your solar panel, be sure to wear your safety goggles all the time.
Source...